New 22" WSM Body has arrived. HELP!

Tim Campbell · Jan 5, 2013

For those that did not see the other threads, I got a new 22 WSM and the body had a dent. I just got a new body, less than three days later. Go Weber. So I set it up and here is a pic of the new machine! I put 1/2 a ring of charcoal in and dumped half a lit chamber. I am using Royal Oak. It screamed up to 425 with all of the vents open. I waited 15 minutes and closed two vents half way. No change. I waited 15 minutes and closed two vents all the way. Came down to 390. I forgot about the water, so I filled the water pan 1/2 way and closed all the vents. It is now settled at 315 for the last 30 minutes.
I have a maverick thermo, on the edge of the top rack. The dome thermo says 300. No wind, temp outside is about 35 degrees. So, did I build too big of a fire?

Tim Campbell · Jan 5, 2013

The 3lb chuck roast that will hopefully go on tomorrow!

Smoothsmoke · Jan 5, 2013

I used to only dump in about 15 briquettes of lite and it always ran rock stead at 260-275F.

You want to start closing your vents on the way up, preferably 50-75F away from your target temperature. If your target temp is 250F, start closing the bottom vents at around 175F, then check in 10-15 minutes, and so forth.

Also since you're WSM is brand spanking new, it will run a bit hotter for the first couple of cooks. Dont worry if you're cooking in the 275-300F, meat will still be GOOOOD.

BBQ Bandit · Jan 5, 2013

Fire rose too fast.

Have used a smaller pile of coals to start with all vents open.
Once the pit temp approached 175 I shut down 2 vents fully.
My WSM runs 300*(empty water pan) on one vent wide open.

As a result: 2/3rds to 3/4 open on one vent works for me.

caseydog · Jan 5, 2013

It sounds to me like you put WAY too many lit coals on, based on what you wrote.

Have you read up on the "Minion Method." You should be starting with something like 90-percent unlit coals, and 10-percent lit coals. Raising the temperature is far easier than lowering it.

I have an 18.5 WSM, and start off with just under half a chimney of lit coals on an almost full ring of coals and wood chunks.

Seriously, if the fire is too hot, you most likely started too hot, and cooling the fire down is not easy. Always err on the too cool side, because that is easier to fix.

CD

Wolverine · Jan 5, 2013

Tim it sounds like you did build to big a fire, You didnt say what you were cooking so I or We dont the situation, First its easer to bring temp up rather than down, I fill the basket with a coffee can in the middle then pull out the can and dump in 12-20 hot coals, lots of info here on the minion method, it works great. Be patient it takes time for it to come to temp. Good luck

volfan411 · Jan 5, 2013

Tim if you have your thermo probe on the outside edge of grate you may get a higher reading. I have a 18.5 and ribs seem to get done on the ends quicker due to the heat rising along edge.

Tim Campbell · Jan 5, 2013

I definitely got over zealous on the chimney. I will do 1/4 chimney tomorrow with the vents open much less

Tim Campbell · Jan 5, 2013

Not cooking anything now. I read somewhere that you should fire up the smoker once without food.

HankB · Jan 5, 2013

Tim Campbell said:
Not cooking anything now. I read somewhere that you should fire up the smoker once without food.

I never did. <shrug>

With no food and no water there is nothing to soak up the heat.

Normally when I close up my cooker, I close two of three bottom vents. (Top vent remains open all the time until I shut down after a smoke.)

A new smoker may not seal as well. My 18.5 held temperature with food and water in the bowl with all bottom vents closed (in summer.)

Did instructions come with the smoker? You may do well to follow them the first few smokes. I know you will get a lot of information that conflicts with that on this site and I won't say that any of it is wrong. However Weber has written instructions that are as bulletproof as they can make them for someone who has never fired up their WSM. That would be a good place to start.

Tim Campbell · Jan 5, 2013

Thanks all!

kds9547 · Jan 5, 2013

I just got the 22.5 WSM about three months ago. The first thing I would tell you is to disregard the temp gauge on the smoker and get a reliable thermometer. My smoker's gauge reads 30-40 degrees high depending on the temp I'm cooking at. I'm still learning but I find that the water pan does make a huge difference. The minion method has worked well for me and I am able to maintain 250 degrees consistently after a few cooks. Cooked a prime rib last week ( my first one ) and it was AWESOME! Plenty of good info from these guys on here.

Smokin' D · Jan 5, 2013

In the drum or the WSM I don't use a chimney at all. 90 seconds with a plumbers torch, leave the vents full open and in a few minutes, beer minutes that is, when the temp hits 200°, start closing the vents. Like the others said, it is easier to heat it up than cool it down!

bo_gator · Jan 5, 2013

Tim Campbell said:
Not cooking anything now. I read somewhere that you should fire up the smoker once without food.

It be hard to eat on nothing :wacko:

Homebrewed Q · Jan 5, 2013

Glad to hear Weber took care of you. You've got some good advice so far, and I'd agree with the temp gauge replacement, find a good one to replace it with. Then again, I never use one when I smoke on my Weber Kettles. For a 6 hour rib smoke I just shut the vents on the bottom to just a sliver opening, vent on top wide open, and dump about a half chimney of lit in a coal basket to one side with a couple of chunks of pecan and put the lid on, add 6-8 coals about 2 hours in, and maybe a few more a couple hours later.

BobM · Jan 5, 2013

I fill my charcoal ring to the top with 4 or 5 fist sized chunks of wood mixed in the charcoal.
I light it in 3 places, in between the vents, with a high output propane torch.
I let it go for about 10 or 15 minutes then put the WSM together.
I bring the cooker slowly up to my cooking temperature, then put the meat on.
I do not use water, I use a foiled clay flower pot base in the foiled water pan.

WSM dome thermometers are accurate for where they are located.
I find it better to measure the temperature at the grate level.

Hope this helps.

Bob

Tim Campbell · Jan 6, 2013

I used a 1/14 chimney of charcoal and half a ring.
The chuckie has settled in at 275

rolfejr · Jan 6, 2013

The new barrel will cook a bit hotter than a seasoned one.
It will be easier to control after a few cooks.

+ 1 on the propane torch for starting the fire, just get a few coals glowing and it will slowly rise, as opposed to trying to bring it down.

Tim Campbell · Jan 6, 2013

Seems to have settled in at 250. I am still working on getting the fire to where I want but it stays where it is, which is nice.

Jethro1 · Jan 6, 2013

You have to catch the temp on the way up, not try and get it to lower back to where you want it. Will save you fuel and time doing that.

New 22" WSM Body has arrived. HELP!

Knows what a fatty is.

Knows what a fatty is.

Babbling Farker

Babbling Farker

somebody shut me the fark up.

is one Smokin' Farker

Knows what a fatty is.

Knows what a fatty is.

Knows what a fatty is.

is Blowin Smoke!

Knows what a fatty is.

is one Smokin' Farker

Attachments

is Blowin Smoke!

bo_gator

Guest

Take a breath!

Babbling Farker

Knows what a fatty is.

Full Fledged Farker

Knows what a fatty is.

Knows what a fatty is.

Similar threads